Customs - Electronic Sealing - Deposit in and removal of goods from Customs Bonded Warehouses - Certain guidelines / instructions - Customs - PUBLIC NOTICE No. 34/2018-Customs

OFFICE OF THE COMMISSIONER OF CUSTOMS (PREVENTNIVE) 55-17-3, C-14, 2nd Floor, Industrial Estate, Autonagar, Vijayawada - 520007 Phone: 0866-2551261 Fax: 0866-2551156 C. No. VIII/09/01/2018-Cus.Tech Date: 20.06.2018 PUBLIC NOTICE No. 34/2018-Customs Subject: - Customs - Electronic Sealing - Deposit in and removal of goods from Customs Bonded Warehouses - Certain guidelines / instructions - Regarding. *** Attention of all the Importers, Exporters, Customs Brokers, Steamer Agents Custodians/Customs Cargo Service Providers, Trade Associations / Chamber of Commerce, Members of the RAC / PGC / CCFC is invited to the Board's Circular No.19/2018-Customs, dated 18.06.2018 issued from F. No.484/3/2015-LC(Vol.II) on guidelines prescribing the procedure on deposit in and removal of goods from Customs Bonded Warehouses. The procedure prescribed is as below: 1. The Warehouse (Custody Handling of Goods) Regulations, 2016, the Special Warehouse (Custody Handling of Goods) Regulations, 2016, Warehoused Goods (Removal) Regulations 2016 and circular 17/2016-Cus prescribe the affixation of a one-time-lock for transport of goods to be deposited in a warehouse or removed therefrom. 2. The regulations require that goods arriving at the warehouse from a customs station shall be affixed with a one-time-lock with its serial number endorsed upon the bill of entry for warehousing and the transport document. The warehouse keeper or bond officer, as the case may be, is required to inspect the seal and when it is found intact, permit the goods to be unloaded at the warehouse. Circular 17/2016- Cus dated 14th May 2016 prescribes that in case of removal of goods from a Customs station for deposit into a warehouse, the container or means of transport (closed trucks) should be affixed with a one-time- lock by the proper officer at the customs station. A similar procedure was provided under the Warehoused Good (Removal) Regulations, 2016, for removal of warehoused goods from one warehouse to another and from a warehouse to customs station for export. Also, the Principal Commissioner of Customs / Commissioner of Customs is duly empowered to permit movement of goods without affixation of OTLs, where the nature of goods or their manner of transport so warrant (e.g. Liquid Bulk Cargo transported through Pipe Lines and Over Dimensional Cargo). 3. Subsequently, the Board had prescribed RFID self-sealing for export of containerized cargo. Circulars 36/2017, 37/2017 and 41/2017 - Customs prescribe the use of RFID tamper proof one time- bolt seal and providing of readers / procedure for its use by Customs. It is now decided by the Board that RFID sealing shall be extended to transport of goods for deposit in a warehouse as well as removal therefrom. Therefore, wherever the Warehousing Regulations (referred in para 1 above) prescribe affixing of a One Time Lock , the importer or owner of the goods shall use RFID anti-tamper one- time-locks (hereinafter referred as RFID OTL ). 4. The RFIDOTLs shall be sourced from the vendors whose names appear on the list placed on the website of the CBIC (please see weblink alongside to Circular 36 37/2017 on www.cbic.gov.in). 4.1 Considering the fact that goods may be removed through a variety of vehicles, different types of RFID OTLs, such as bolt seals (already specified by circular 36/2017-Cus) or wire - cable seal shall be used. The specifications, data elements and procedure to be used under the Regulations for Warehousing shall be as follows. 4.2 Seals (i) For containers (RFID One-Time-Bolt Seal) As prescribed under circular 36/2017- Customs dated 28 th August 2017 (ii) For closed body vehicles (RFID Wire Cable seal) (a) Each seal shall be a one-time-lock bearing a unique serial number and brand of the vendor in the format ABCD XXXX XXXX, where ABCD stands for the brand of the vendor and X (8 digit) is a numerical digit from 0-9 (b) The RFID seal shall conform to ISO 17712:2013 and ISO/IEC 18000-6 Class 1 Gen 2 which is globally accepted in industrial applications and can be read with the use of UHF (i.e. 860 MHz to 960) Reader-Scanners. (c) The manufacturer or vendor, as the case may be, shall be in possession of certifications required for conformance of the ISO standard ISO 17712:2013 namely, clauses 4, 5 and 6 (as applicable to cable-wire seals) (d) Before commencement of sales, the vendor shall submit self-certified copies of the above certifications to the Risk Management Division (RMD) 4.3 Readers The specification of Readers to be deployed shall be as prescribed under circular 41/2017 - Customs dated 30.10.2017. 4.4 Software Application (a) The data elements to be captured in the web-application in the case of removal goods from a customs station to a bonded warehouse shall be as follows: (i) IEC (Importer Exporter Code) (ii) Bill of Entry Number. (iii) Date (iv) RFID OTL number (v) Date of sealing (vi) Time of sealing (vii) Container Number (where cargo is containerized or else not required) (viii) Registration number of vehicle (ix) Warehouse code (x) Customs location code (b) The data elements to be captured in the web-application in the case of removal goods from a warehouse t a customs station for export shall be as follows: (i) IEC (Importer Exporter Code) (ii) Shipping Bill Number. (iii) Date (iv) RFID OTL number (v) Date of sealing (vi) Time of sealing (vii) Container Number (where cargo is containerized or else not required) (viii) Registration number of vehicle (ix) Customs location code (x) Warehouse code (c) The data elements to be captured in the web-application in the case of removal goods from a warehouse to another warehouse (Section 67)shall be as follows: (i) IEC (Importer Exporter Code) (ii) Bill of Entry Number. (iii) Date (iv) Warehouse code (Origin) (v) Warehouse code (destination) (vi) REID OTL number (vii) Date of sealing (viii) Time of sealing (ix) Container Number (where cargo is containerized or else not required) (x) Registration number of vehicle 4.5 Procedure a) All licensees of customs bonded warehouses shall have to procure Readers for scanning of RFID OTLs at the bonded warehouse at their own cost. b) The licensee shall also procure REID OTLs from the vendors for providing the same to importer, owner, exporter or in case of private bonded warehouses for their own use. It is clarified that licensees are free to procure RFID OTLS from any one or more vendors. c) The vedors shall be required to provide Readers to Customs locations. Readers already deployed by vendors to Ports and ICDs for RFID sealing can also be used for the procedure. Air Cargo Complexes, CFS and LCSs are also covered under this procedure for transport of bonded goods. d) Any importer permitted to remove goods for deposit in a warehouse shall obtain an RFID seal from the Warehouse where the goods are to be deposited. e) Vendors shall ensure that TID number is captured in their data base and warehouse code of the licencee is linked to the same at the time of sale of seals. f) Vendors shall ensure that data can be uploaded from internet enabled Readers as well as desktops. g) Circular No. 19/2016-Cus dated 20th May, 2016 prescribes that the importer shall declare the warehouse code in the Bill of Entry for warehousing. The Out of Charge Officer releasing the cargo for deposit in a warehouse is advised to match the warehouse code declared in the bill of entry with that linked to the seal. This procedure shall dispense the need for securing any space availability certificates by importers. h) The exporter of warehoused goods will be obligated to declare the physical serial number of the RFID OTL at the time of filing the online integrated shipping bill or in the case of manual shipping bill, before the container or cargo is dispatched from the warehouse. i) In case the RFID OTL is found to be tampered at the Customs Station at the time of export, then mandatory examination would be carried out by the Customs authorities. j) In case at the time of arrival of the goods at the warehouse, the RFID OTL is found to be tampered, then the licencee shall hot permit unloading of the goods and shall inform the Bond Officer (please refer sub-regulation 5(1) and (7) of the Warehouse Custody Handling of Goods Regulations, 2016). k) Under Regulation (5) of the Warehoused Goods (Removal) Regulations, 2016, the importer or owner is required to produce an acknowledgement of the due arrival of the goods. A period of one month (or as extended by the proper officer) has been provided under the regulations for producing the acknowledgement, failing which, the owner of the goods is required to pay full duties along with interest, fine and penalty. With the introduction of the procedure contained in this circular, the trip report generated by scanning the RFID OTL at the destination customs station or warehouse, shall be printed and retained for records by the Customs Station, bond officer and licencee. This will enable discharge of the requirement of acknowledgement enjoined under the regulation (5). However, this is notwithstanding the obligation cast on the licencee under Warehouse (Custody Handling) Regulations 2016 for accountal of goods [Regulation (5) and (7) refer]. l) For the purpose of risk management, if there is any inordinate delay in the due arrival of goods, the bond officer may alerted by the customs station or vice versa. m) Where any procedure requires that goods removed from a warehouse shall move under physical escort by customs (eg. As prescribed by circular 32/2016 regarding Duty Free Shops), the use of RFID OTL shall not apply. 5. The Principal Commissioner of Customs / Commissioner of customs is duly empowered to permit movement of goods without affixation of RFID OTLs, where the nature of goods or their manner of transport so warrant (e.g. Liquid Bulk Cargo transported through Pipe Lines and Over Dimensional Cargo). 6. The above procedure shall come into force with effect from 1 st August, 2018. 7. Action to be taken in terms of the decisions taken in this Public Notice should be considered as Standing Order for the purpose of officers and staff. 8. Difficulties, if any, in implementation of this Public Notice may be brought to the notice of the Commissioner of Customs (Preventive), Vijayawada. (SUDHA KOKA) COMMISSIONER